SL-1110 S-7550A HIGH SPEED SINGLE NEEDLE STRAIGHT LOCK STITCHER Please read this manual before using the machine. Please keep this manual within easy
SL-1110 5. INSTALLATION 3 5. INSTALLATION CAUTION Machine installation should only be carried out by a qualified technician. Contact your Br
SL-1110 5. INSTALLATION44. Machine head (1) Hinges [2 pcs] (2) Machine head (3) Head rest NOTE: Tap the head rest (3) securely into the table hol
SL-1110 5. INSTALLATION 56. V-belt (1) motor (Sold separately) (2) V-belt (Sold separately) * Turn the two nuts (3) to adjust so that there is
SL-1110 5. INSTALLATION63. Return the machine head to its original position, and then remove the screw (4) from the rear of the machine head.
SL-1110 5. INSTALLATION 77. Insert the cover (9) of belt cover D (7) in between the belt cover (2) and belt cover D (7), and then place it into the
SL-1110 5. INSTALLATION85-2. Ground wire connections Use the correct type of ground wire. (Be sure to read the instruction manual for the motor tog
SL-1110 6. PREPARATION BEFORE SEWING 96. PREPARATION BEFORE SEWING 6-1. Installing the needle CAUTION Turn off the power switch before installing t
SL-1110 6. PREPARATION BEFORE SEWING106-3. Winding the lower thread CAUTION Do not touch any of the moving parts or press any objects against the m
SL-1110 6. PREPARATION BEFORE SEWING 116-5. Threading the upper thread CAUTION Turn off the power switch before threading the upper thread. The mot
SL-1110 7. SEWING127. SEWING CAUTION Attach all safety devices before using the sewing machine. If the machine is used without these devices attach
SL-1110 Thank you very much for buying a BROTHER sewing machine. Before using your new machine, please read the safety instructions and the explanat
SL-1110 8. THREAD TENSION 138. THREAD TENSION 8-1. Adjusting the thread tension CAUTION Turn off the power switch before removing or inserting the
SL-1110 8. THREAD TENSION9. CLEANING148-2. Adjusting the presser foot pressure Correct stitches Upper thread Skipped stitches occu
SL-1110 9. CLEANING 155. Tilt back the machine head. 6. Remove the bobbin case (4). 7. Wipe off any dust from the rotary hook (5) with a soft clo
SL-1110 10. STANDARD ADJUSTMENTS1610. STANDARD ADJUSTMENTS CAUTION Maintenance and inspection of the sewing machine should only be carried ou
SL-1110 10. STANDARD ADJUSTMENTS 1710-2. Adjusting arm thread guide R The standard position of arm thread guide R (1) is the position where the scre
SL-1110 10. STANDARD ADJUSTMENTS1810-4. Adjusting of the feed dog height The standard height of the feed dog (1) when it is at its maximum height ab
SL-1110 10. STANDARD ADJUSTMENTS 1910-6. Adjusting the needle bar height Reference line (a), which is the second line from the bottom of the needle
SL-1110 10. STANDARD ADJUSTMENTS2010-8. Adjusting the needle and rotary hook timing The tip of the rotary hook (3) should be aligned with the center
SL-1110 10. STANDARD ADJUSTMENTS 2110-9. Adjusting the rotary hook lubrication amount CAUTION Be careful not to touch your fingers or the lubricati
SL-1110 11. TROUBLESHOOTING2211. TROUBLESHOOTING yPlease check the following points before calling for repairs or service. yIf the following remed
SL-1110 i SAFETY INSTRUCTIONS [1] Safety indications and their meanings This instruction manual and the indications and symbols that are used on the
SL-1110 11. TROUBLESHOOTING 23 Problem Possible cause Page 5 Skipped stitches at sewing start Thread unravelling at sewing start yIs the thread ta
SL-1110 11. TROUBLESHOOTING24 Problem Possible cause Page 9 Lower thread is tangled at the sewing start. yIs the bobbin spinning direction correc
INSTRUCTION MANUAL SL-1110, S-7550ASA8760-1012007.06.BC(1)http://www.brother.com/
SL-1110 ii[2] Notes on safety CAUTION Environmental requirements Use the sewing machine in an area which is free from sources of strong
SL-1110 iii CAUTION Sewing This sewing machine should only be used by operators who have received the necessary training in safe use befor
SL-1110 iv[3] Warning labels The following warning labels appear on the sewing machine. Please follow the instructions on the labels at all times whe
SL-1110 CONTENTS 1. NAMES OF MAJOR PARTS... 1 2. MACHINE SPECIFICATIONS... 1 3. TABLE...
SL-1110 1. NAMES OF MAJOR PARTS 2. MACHINE SPECIFICATIONS 11. NAMES OF MAJOR PARTS (1) Needle plate (2) Presser foot (3)
SL-1110 3. TABLE 4. MOTOR23. TABLE Table processing diagram yThe top of the table should be 40 mm in thickness and should be strong enough to hold
Comments to this Manuals