Brother S-1110A Instruction Manual

S-1110A Please read this manual before using the machine. Please keep this manual within easy reach for quick reference. HIGH SPEED SINGLE NEEDLE STR

S-1110A 5. INSTALLATION 3 5. INSTALLATION CAUTION Machine installation should only be carried out by a qualified technician. Contact your Br

S-1110A 5. INSTALLATION44. Machine head (1) Hinges [2 pcs] (2) Machine head (3) Head rest NOTE: Tap the head rest (3) securely into the table hol

S-1110A 5. INSTALLATION 5 6. V-belt (1) motor (Sold separately) (2) V-belt (Sold separately) * Turn the two nuts (3) to adjust so that there is 1

S-1110A 5. INSTALLATION63. Return the machine head to its original position, and then remove the screw (4) from the rear of the machine head.

S-1110A 5. INSTALLATION 7 7. Insert the cover (9) of belt cover D (7) in between the belt cover (2) and belt cover D (7), and then place it into th

S-1110A 5. INSTALLATION85-2. Ground wire connections Use the correct type of ground wire. (Be sure to read the instruction manual for the motor tog

S-1110A 6. PREPARATION BEFORE SEWING 9 6. PREPARATION BEFORE SEWING 6-1. Installing the needle CAUTION Turn off the power switch before installing

S-1110A 6. PREPARATION BEFORE SEWING106-3. Winding the lower thread CAUTION Do not touch any of the moving parts or press any objects against the m

S-1110A 6. PREPARATION BEFORE SEWING 11 6-5. Threading the upper thread CAUTION Turn off the power switch before threading the upper thread. The mo

S-1110A 7. SEWING127. SEWING CAUTION Attach all safety devices before using the sewing machine. If the machine is used without these devices attach

S-1110A Thank you very much for buying a BROTHER sewing machine. Before using your new machine, please read the safety instructions and the explana

S-1110A 8. THREAD TENSION 13 8. THREAD TENSION 8-1. Adjusting the thread tension CAUTION Turn off the power switch before removing or inserting th

S-1110A 8. THREAD TENSION9. CLEANING148-2. Adjusting the presser foot pressure Correct stitches Skipped stitches occur Increase

S-1110A 9. CLEANING 15 5. Tilt back the machine head. 6. Remove the bobbin case (4). 7. Wipe off any dust from the rotary hook (5) with a soft cl

S-1110A 10. STANDARD ADJUSTMENTS1610. STANDARD ADJUSTMENTS CAUTION Maintenance and inspection of the sewing machine should only be carried ou

S-1110A 10. STANDARD ADJUSTMENTS 17 10-2. Adjusting arm thread guide R The standard position of arm thread guide R (1) is the position where the scr

S-1110A 10. STANDARD ADJUSTMENTS1810-4. Adjusting of the feed dog height The standard height of the feed dog (1) when it is at its maximum height ab

S-1110A 10. STANDARD ADJUSTMENTS 19 10-6. Adjusting the needle bar height Reference line (a), which is the second line from the bottom of the needle

S-1110A 10. STANDARD ADJUSTMENTS2010-8. Adjusting the needle and rotary hook timing The tip of the rotary hook (3) should be aligned with the center

S-1110A 10. STANDARD ADJUSTMENTS 21 10-9. Adjusting the rotary hook lubrication amount CAUTION Be careful not to touch your fingers or the lubricat

S-1110A 11. TROUBLESHOOTING2211. TROUBLESHOOTING y Please check the following points before calling for repairs or service. y If the following re

S-1110A i SAFETY INSTRUCTIONS [1] Safety indications and their meanings This instruction manual and the indications and symbols that are used on the

S-1110A 11. TROUBLESHOOTING 23 Problem Possible cause Page 5 Skipped stitches at sewing start Thread unravelling at sewing start y Is the thread

S-1110A 11. TROUBLESHOOTING24 Problem Possible cause Page 9 Lower thread is tangled at the sewing start. y Is the bobbin spinning direction corr

INSTRUCTION MANUAL S-1110ASB3026-0012011.08. ZC (1)http://www.brother.com/ © 2011 Brother Industries, Ltd. All Rights Reserved. This is the o

S-1110A ii [2] Notes on safety CAUTION Environmental requirements Use the sewing machine in an area which is free from sources of stro

S-1110A iii CAUTION Sewing This sewing machine should only be used by operators who have received the necessary training in safe use befo

S-1110A iv [3] Warning labels The following warning labels appear on the sewing machine. Please follow the instructions on the labels at all times w

S-1110A CONTENTS 1. NAMES OF MAJOR PARTS ... 1 2. MACHINE SPECIFICATIONS ... 1 3. TABLE ...

S-1110A 1. NAMES OF MAJOR PARTS 2. MACHINE SPECIFICATIONS 1 1. NAMES OF MAJOR PARTS (1) Needle plate (2) Presser foot (3

S-1110A 3. TABLE 4. MOTOR23. TABLE Table processing diagram ・ The top of the table should be 40 mm in thickness and should be strong enough to hold