Brother HE-8000 Instruction Manual Page 81
- Page / 106
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
10. TABLE OF ERROR CODES
HE-800B
72
Code Cause Remedy
Page
E050
Machine head tilting was detected
immediately before the sewing machine
started operating.
Turn off the power, and then return the machine head to its
original position.
Check that safety switch connector P14 on the main P.C.
board is properly connected.
10*
E051
Machine head tilting was detected while
the sewing machine was operating.
Turn off the power, and then return the machine head to its
original position.
Check that safety switch connector P14 on the main P.C.
board is properly connected.
10*
E055
Machine head tilting was detected when
the power was turned on.
Turn off the power, and then return the machine head to its
original position.
Check that safety switch connector P14 on the main P.C.
board is properly connected.
10*
E065
An operation panel key was still being
pressed when the power was turned on,
or key is faulty.
Turn off the power and check the operation panel.
*
Upper shaft motor-related errors
Items with a “*” in the “Page” column should only be handled by a qualified technician.
Code Cause Remedy Page
E110
Pulley is not in needle up stop position
during standby when work clamp is
lowered.
Turn off the power, and then open the slide cover. Align
the mark (A) on the pulley within the edges of the mark (B)
on the motor cover.
*
E111
The sewing machine could not stop
correctly at the needle up stop position
after sewing.
Turn off the power, and then check that there are no
problems with the cutter mechanism, the thread trimming
mechanism and the upper shaft motor mechanism.
*
E112
The needle bar dropped during home
position detection or while the SD card
was being accessed.
Turn off the power, and then turn it back on again.
* If this error occurs when the work clamp is not lowered,
the work clamp will drop automatically in order to
prevent interference between the needle and the lower
thread retainer.
–
E113
Pulley is not in needle up stop position
during standby when work clamp is not
lowered.
Turn off the power, and then open the slide cover. Align the
mark (A) on the pulley within the edges of the mark (B) on
the motor cover. (Refer to the diagram for “E110” above.)
* If this error occurs, the work clamp will drop
automatically in order to prevent interference between
the needle and the lower thread retainer.
*
E130
Upper shaft motor stopped due to a
problem, or synchronizer is faulty.
Turn off the power, and then open the slide cover. Turn
the pulley to check if the machine has locked up.
Check that the upper shaft motor 4-pin (UVW) connector
and synchronizer connector P11 on the motor P.C. board
are properly connected.
*
11*
E131 Synchronizer is not connected correctly.
Turn off the power, and then check that synchronizer
connector P11 on the motor P.C. board is properly
connected.
11*
4886M
- HE-800B 1
- SAFETY INSTRUCTIONS 3
- WARNING 3
- [3] Warning labels 6
- CONTENTS 8
- 1. NAMES OF MAJOR PARTS 10
- 2. SPECIFICATIONS 11
- 3. INSTALLATION 13
- CAUTION 14
- 3-4. Installing the bed base 15
- 3-9. Connecting the cords 18
- Lock the cord 19
- CAUTION 23
- Green and yellow wire 27
- (ground wire) 27
- Operator 27
- Set so that there is 29
- 4. PREPARATION BEFORE SEWING 30
- Flashing 32
- 4-5. Thread tension 35
- 4-5-2. Upper thread tension 36
- Stronger 37
- Index mark 37
- Sewing area 40
- 5-3. Operating the treadle 41
- 5-4. Program setting method 42
- Shortcut keys 43
- 5-4-1. Parameter list 44
- 1: 2: 3: 4: 45
- 5-6. Underlay programs 52
- 5-7. Cutter operation 53
- 5-8. Copying programs 54
- 6-2. Test feeding mode 57
- Number of stitches 58
- 6-3. Using the STOP switch 59
- 7-1. Using cycle programs 61
- 7-2. Setting memory switches 64
- 8. CLEANING 70
- 8-2. Draining the oil 71
- 8-4. Cleaning the eye guard 72
- 8-5. Checking the needle 72
- 9. STANDARD ADJUSTMENTS 73
- 0.01 – 0.08 mm 75
- Becomes 79
- 10. TABLE OF ERROR CODES 80
- 11. TROUBLESHOOTING 86
- 11-2. Skipped stitches 87
- Needle plate hole 93
- Adjust the rotary hook 93
- Check flaw here 93
- 11-13. Upper thread run out 94
- Cotton yarn #60 97
- Holding force approx. 2N 97
- 11-17. Needle breakage 99
- Cutter sensor 100
- 0.5 mm 100
- 11-21. Seam is cut 101
- Approx. 1 mm 102
- Thread driving arm 105
- INSTRUCTION MANUAL 106
Comments to this Manuals
Related products and manuals for Sewing machines Brother HE-8000
Sewing machines Brother CE-8080 User Manual
(104 pages)
(104 pages)
Sewing machines Brother CS-80 Instruction Manual
(115 pages)
(115 pages)
Sewing machines Brother PC-4000 User Manual
(12 pages)
(12 pages)
(100 pages)
Sewing machines Brother HS-2000 User Manual
(19 pages)
(19 pages)
(63 pages)
Sewing machines Brother 885-U26 User Manual
(124 pages)
(124 pages)
Sewing machines Brother BAS-375 User Manual
(122 pages)
(122 pages)
© 2020, manymanuals.com. All rights reserved. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
brother HE-8000-2 button hole machine error E-44