Brother BAS-326 Service Manual

BAS-311E,311ELBAS-326E,326ELSERVICE MANUALPROGRAMMABLE ELECTRONIC PATTERN SEWERWITH CYLINDER BEDPlease read this manual before making any adjustments.

2BAS-311E.311EL.326E.326ELChapter 1. Mechanical description2. Work clamp lifting mechanism (1) (Solenoid type), 311E1. When the presser signal is on,

92BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment10. Confirming software version1. While pressing the TEST switch q,

93BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment11. Error codesNOTE ¡If an operation problem occurs, a buzzer will s

94BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustmentWait at least 5 minutes after turning off the power switch and disco

95BAS-311E.311EL.326E.326ELChapter 7Chapter 7. Trouble shootingOFF Explanation of shapesIndicates manual operation.Indicates switch operation.Selects

96BAS-311E.311EL.326E.326ELChapter 7YESNOYESNONOYESPress the PRO NO. Switch, then press the R/W switch.Step on the Foot switch. Does an error code a

97BAS-311E.311EL.326E.326ELChapter 7Input sewing data.Step on the foot switch to close the work clamp.Step on the presser plate lifter switch.#6#8OFF#

98BAS-311E.311EL.326E.326ELChapter 7TestPress the TEST switch.Step on the start foot switch.Step on the presser plate lifter switch.Release the presse

99BAS-311E.311EL.326E.326ELChapter 7Sewing operationPress the TEST switch to turn off the TEST lamp.Step on the start foot switch.YESNODoes an error c

100BAS-311E.311EL.326E.326ELChapter 7Emergencystop andrestartingoperationProgramingdevicePress the EM switch while sewing.Press the EM switch again.Pr

101BAS-311E.311EL.326E.326ELChapter 7 Problem solution and measuresPrecautions¡ Pay attention to the following when opening the control box for maint

3BAS-311E.311EL.326E.326ELChapter 1. Mechanical descriptionWork clamp lifting mechanism (2) 311E, 311EL(Pneumatictype)1. When the air cylinder q opera

102BAS-311E.311EL.326E.326ELChapter 7#1 The power lamp does not light when the power is turned on. Probable causes1. Conversion transformer improperly

103BAS-311E.311EL.326E.326ELChapter 7#1 continued Probable causes4. Fuse has blown 5. Power supply circuit board  defective6. Control circuit board de

104BAS-311E.311EL.326E.326ELChapter 7#1 The power lamp does not light when the power is turned on. Probable causes1. With error code [E.12], the eme

105BAS-311E.311EL.326E.326ELChapter 7#1.2No switches on the panel are not activated.#2 If the R/W switch is pressed, the indicator lamp is not lit an

106BAS-311E.311EL.326E.326ELChapter 7#3After a few seconds after the R/W switch is pressed, an error code appears.#4The work clamp does not move up an

107BAS-311E.311EL.326E.326ELChapter 7#4The work clamp does not move up and down when the foot switch is stepped on. Probable causes4. Power PCB defec

108BAS-311E.311EL.326E.326ELChapter 7#4The work clamp does not move up and down when the foot switch is stepped on.#6When the start switch is stepped

109BAS-311E.311EL.326E.326ELChapter 7#8The work clamp does not move to the sewing start position.#9The TEST lamp is not lit when the TEST switch is pr

110BAS-311E.311EL.326E.326ELChapter 7#13The machine does not operate for sewing and error [E.20] appears.#14After the machine operates, an error code

111BAS-311E.311EL.326E.326ELChapter 7#17The machine does not stop with the needle at the upper position.#18The machine can not sew patterns as pro-gra

4BAS-311E.311EL.326E.326ELChapter 1. Mechanical description3. Feed mechanism (X axis) 311E, 311EL, 326E, 326EL1. When X-timing pulley A326 w attached

112BAS-311E.311EL.326E.326ELChapter 8.Chapter 8. 1. Gauge parts list according to subclassesThe following parts are available for the BAS-311E, 311EL,

113BAS-311E.311EL.326E.326ELChapter 9. Gauge parts listRef.No.ERef.No.XYRef.No.BRef.No.FRef.No.CRef.No.GRef.No.DRef.No.JRef.No.A *ø4ø2.55ø5.5ø45ø3ø25ø

114BAS-311E.311EL.326E.326ELChapter 9. Gauge parts list Work clamp, Feed plate (BAS-311E)CODEQTY NAME OF PARTSREF.NO.6789107375-175-2140-1140-275-375

115BAS-311E.311EL.326E.326ELChapter 9. Gauge parts listCODEQTY NAME OF PARTSREF.NO.138150-1150-2150-3152154153-1153-2153-3153-4153-5153-6153-789898920

116BAS-311E.311EL.326E.326ELChapter 9. Gauge parts list Work clamp and Feed plate (BAS-311EL)CODEQTY NAME OF PARTSREF.NO.6789107375-175-2140-275-375-

117BAS-311E.311EL.326E.326ELChapter 9. Gauge parts list Feed plate blank and Work clamp blank (BAS-311EL)CODE QTY NAME OF PARTSREF.NO.898989138150-11

118BAS-311E.311EL.326E.326ELChapter 9. Gauge parts list Feed mechanism (BAS-326E)CODE QTY NAME OF PARTSREF.NO.7375-175-276777891140140-1140140-25575-

119BAS-311E.311EL.326E.326ELChapter 9. Gauge parts list Feed mechanism (Option parts) BAS-326ECODE QTY NAME OF PARTSREF.NO.138155150-1150-2150-315215

120BAS-311E.311EL.326E.326ELChapter 9. Gauge parts list Feed mechanism (BAS-326E, 326EL)CODE QTY NAME OF PARTSREF.NO.667789107375-175-2140-1140-2575-

121BAS-311E.311EL.326E.326ELChapter 9. Gauge parts list Feed mechanism (Option parts)10.50.10.60.10.6138155150-1272136164248150-3272136164248150-2272

5BAS-311E.311EL.326E.326ELChapter 1. Mechanical descriptionFeed mechanism (Y axis) 311E and 311EL1. The driving gear w attached to the Y-pulse motor q

122BAS-311E.311EL.326E.326ELChapter 9. Gauge parts list Feed mechanism (Option parts) BAS-326E,326ELCODE QTY NAME OF PARTSREF.NO.151-1151-2151-315515

123BAS-311E.311EL.326E.326ELChapter 10. Option partsChapter 10. Option parts Programmer assy Inner clamp device One-touch clampingdevice Milling d

124BAS-311E.311EL.326E.326ELChapter 10. Option parts ProgrammerCODE QTY NAME OF PARTSREF.NO.11-11-21-31-41-51-61-71-81-91-101-111-121-131-141-151-161

125BAS-311E.311EL.326E.326ELChapter 10. Option parts Inner clamping device (Option device)CODE QTY NAME OF PARTSREF.NO.11-11-1-11-1-21-1-31-1-41-1-51

126BAS-311E.311EL.326E.326ELChapter 10. Option parts Inner clamping device (Option device) BAS-326EL1-11-71-11-911-1-151-11-61-131-1-11-1-171-1-241-1-

127BAS-311E.311EL.326E.326ELChapter 10. Option parts One-touch work clampCODE QTY NAME OF PARTSREF.NO.1233-13-23-33-43-544-14-255-15-23-13-2CODES2461

128BAS-311E.311EL.326E.326ELChapter 10. Option parts3-44-15-13-33-23-133-56-16-23-54-25-254 One-touch work clamp (Option parts) BAS-326ELFor Supplry

129BAS-311E.311EL.326E.326ELChapter 10. Option parts Snap fastener and hook attachment deviceM-525KM-528KM-520KM-533KOM ø7.6,ø8.6M-508KCODE QTY NAME

130BAS-311E.311EL.326E.326ELChapter 10. Option partsCODE QTY NAME OF PARTSREF.NO.23S13099001S1310000111<For Sewing the belt with hook>NEEDLE PLA

131BAS-311E.311EL.326E.326ELChapter 10. Option partsPARTS CORDHOOK SIZE (mm)SNAP SIZE (mm)SHAPE310-HSQ DEVICE UNITM-508     MALES24605-101OM Ø7.6,Ø8

6BAS-311E.311EL.326E.326ELChapter 1. Mechanical description4. Presser foot mechanism (1)1. When the upper shaft q rotates, the stepping work clamp cam

132BAS-311E.311EL.326E.326ELChapter 10. Option partsPARTS CORDHOOK SIZE (mm)SNAP SIZE (mm)310-HS DEVICE UNITM-508 MALES18581-001OM Ø7.6,

133BAS-311E.311EL.326E.326ELChapter 10. Option parts Wide perfect deviceCODE QTY NAME OF PARTSREF.NO.11-1-11-21-31-4-11-4-1-11-5-11-6-1CODES44795001S

134BAS-311E.311EL.326E.326ELChapter 10. Option parts Needle cooler setCODE QTY NAME OF PARTSREF.NO.44-14-24-34-3-14-3-24-3-2-14-3-2-24-3-34-3-44-44-5

135BAS-311E.311EL.326E.326ELChapter 10. Option parts Play prevention work clamp For Horizontal WiperCODE QTY NAME OF PARTSREF.NO.2728293031323334353

136BAS-311E.311EL.326E.326ELChapter 10. Option parts Thread wiper set: Pneumatic typeCODE QTY NAME OF PARTSREF.NO.33-13-1-13-1-23-1-33-1-43-1-53-1-63

137BAS-311E.311EL.326E.326ELChapter 10. Option parts 2-step tension deviceCODE QTY NAME OF PARTSREF.NO.22-1-12-1-1-12-1-1-22-1-1-32-1-1-42-1-1-52-1-1

138BAS-311E.311EL.326E.326ELChapter 10. Option parts Auxiliary device11-21-1-131-1-121-1-111-1-11-1-21-1-31-1-51-1-71-1-61-1-41-1-91-1-101-1-82-1-32-

139BAS-311E.311EL.326E.326ELChapter 10. Option partsCODE QTY NAME OF PARTSREF.NO.11-11-1-11-1-21-1-31-1-41-1-51-1-61-1-71-1-81-1-91-1-101-1-111-1-121-

140BAS-311E.311EL.326E.326ELControl Block DiagramSynchronizerHeadEM switchPresser tootSolenoidPresser plateSolenoidThread trimerSolenoidWiperSolenoidS

141BAS-311E.311EL.326E.326ELOperation panel boxControl PCBPanel PCBProgrammerunitPROGRAMMERInverterPower supply plugPower switchFilterConvertiontrans-

7BAS-311E.311EL.326E.326ELChapter 1. Mechanical descriptionPresser foot mechanism (2)1. When the stepping work clamp signal is on, the stepping soleno

SERVICE MANUALBROTHER INDUSTRIES,LTD. NAGOYA,JAPANPrinted in Japan151-V11, V12, V26I90807641999. 08. B (1)

8BAS-311E.311EL.326E.326ELChapter 1. Mechanical description5. Thread trimmer mechanism1. When the thread trimmer signal is on, the thread trimming sol

9BAS-311E.311EL.326E.326ELChapter 1. Mechanical description6. Thread nipper (1) when presser foot rises1. When the machine stops, the stepping solen

10BAS-311E.311EL.326E.326ELChapter 1. Mechanical description7. Thread wiper (1) (vertical wiper: standard)1. After thread trimming, the thread wiper s

11BAS-311E.311EL.326E.326ELChapter 2. DisassemblyChapter 2. Disassembly1. Covers (1) 311E1. Remove the screw, the top cover q, the belt covers w and t

iBAS-311E.311EL.326E.326ELThis service manual is intended for BAS-311E, 311EL and 326E; be sure to read the BAS-311E, 311EL,and 326E, 326EL instructio

12BAS-311E.311EL.326E.326ELChapter 2. DisassemblyCovers (2) 311EL1. Remove the screws, the top cover q, the belt cover w, and the frame side cover e.2

13BAS-311E.311EL.326E.326ELChapter 2. Disassembly2. Feed mechanism1. Remove the screw, the needle q and the presser foot w and finger guard e.2. Remov

14BAS-311E.311EL.326E.326ELChapter 2. Disassembly3. Presser foot mechanism1. Loosen the nut q, remove the adjust screw w, the spring guide e, and the

15BAS-311E.311EL.326E.326ELChapter 2. Disassembly4. Needle bar mechanism1. Remove the rubber cap q.2. Remove the needle bar thread guide w from the ne

16BAS-311E.311EL.326E.326ELChapter 2. Disassembly5. Upper shaft mechanism1. Loosen the screw w and the set screw e of thread take-up crank q.(The scre

17BAS-311E.311EL.326E.326ELChapter 2. Disassembly6. Feed mechanism (Y axis) (1) 311E and 311EL1. Loosen the set screw and remove the X-feed shaft q.2.

18BAS-311E.311EL.326E.326ELChapter 2. DisassemblyFeed mechanism (Y axis) (2)1. Remove the bolts, the Y-feed guide assembly q, the cross roller w, and

19BAS-311E.311EL.326E.326ELChapter 2. DisassemblyFeed mechanism (Y axis) (3) 326E, 326E1. Secure the slider support shaft w of the work clamp assy q u

20BAS-311E.311EL.326E.326ELChapter 2. Disassembly7. Feed mechanism (X axis) (1) 311E1. Remove the rubber cap q.2. Loosen the set screws of X-timing pu

21BAS-311E.311EL.326E.326ELChapter 2. DisassemblyFeed mechanism (X axis) (2) 311EL and 326E, 326EL1. Remove the bolt w and the washer e of X-pulley br

iiBAS-311E.311EL.326E.326ELSewingBe sure to wear protective goggles andgloves when handling the lubricating oil andgrease, so that they do not get int

22BAS-311E.311EL.326E.326ELChapter 2. Disassembly8. Lower shaft mechanism1. Tilt the machine head until it stops.2. Remove the bobbin case q and the s

23BAS-311E.311EL.326E.326ELChapter 2. Disassembly9. Work clamp lifter (Solenoid type)1. Remove the spring q.2. Remove the screw w, and the presser sol

24BAS-311E.311EL.326E.326ELChapter 2. Disassembly10. Thread nipper mechanism1. Remove the set screw, the thread tension q, the pin w, and the tension

25BAS-311E.311EL.326E.326ELChapter 2. Disassembly11. Thread trimmer mechanism1. Remove the screws q, the flat screws w and the needle plate e.2. Remov

26BAS-311E.311EL.326E.326ELChapter 3. AssemblyChapter 3. Assembly1. Thread trimmer mechanism (1)1. Insert the driving lever shaft q into the machine.

27BAS-311E.311EL.326E.326ELChapter 3. Assembly2. Thread nipper mechanism1. Pass the tension release assembly q from the bottom ofthe machine to the to

28BAS-311E.311EL.326E.326ELChapter 3. Assembly11.Attach the tension release bar !4, the pin !5 and thethread tension assembly !6 to the machine. Fit t

29BAS-311E.311EL.326E.326ELChapter 3. Assembly3. Work clamp lifter mechanism1. Attach the presser plate q to the presser bar lifter lever rubber w, an

30BAS-311E.311EL.326E.326ELChapter 3. AssemblyMake sure that work clamp easily moves up and down, and apply grease to sliding portions to assemble par

31BAS-311E.311EL.326E.326ELChapter 3. Assembly4. Feed mechanism (X axis) 311E1. Fit the ball bearings q on X-pulley bracket L, and passthe X-timing pu

iiiBAS-311E.311EL.326E.326ELBe sure to wear protective goggles andgloves when handling the lubricating oil andgrease, so that they do not get into you

32BAS-311E.311EL.326E.326ELChapter 3. Assembly5. Attach the linear guide !5, the X-feed bracket !6, and theX-feed guide !7 to the bed using the three

33BAS-311E.311EL.326E.326ELChapter 3. AssemblyFeed mechanism (X axis) 311EL, 326E1. Place X-timing belt B326 w between the two timing belt spacers e o

34BAS-311E.311EL.326E.326ELChapter 3. AssemblyFeed mechanism (X axis) 311EL and 326E4. Position X-timing pulley B326 !6, which is attached to X-pulley

35BAS-311E.311EL.326E.326ELChapter 3. AssemblyFeed mechanism (Y axis) 311E and 311EL1. Loop the Y-timing belt q around the Y-driving pulse mo-tor brac

36BAS-311E.311EL.326E.326ELChapter 3. Assembly9. Attach the Y-axis feed guide @0 to the left of the X-feedbracket @1, pressing the former against the

37BAS-311E.311EL.326E.326ELChapter 3. AssemblyFeed mechanism (Y axis) 326E1. Engage the driving gear w embedded in the Y-feed pulse motor bracket q wi

38BAS-311E.311EL.326E.326ELChapter 3. Assembly5. Temporarily attach the work clamp Arm !2 to the Y-feed bracket i using the bolts and washers.6. Tempo

39BAS-311E.311EL.326E.326ELChapter 3. Assembly6. Upper shaft mechanism1. Insert the upper shaft q from the rear of the machine, and place the thread t

40BAS-311E.311EL.326E.326ELChapter 3. Assembly7. Needle bar mechanism1. Temporarily tighten the screw w of the needle bar guide q.2. Pass the thread t

41BAS-311E.311EL.326E.326ELChapter 3. Assembly8. Presser foot mechanism1. Insert the presser bar w into the presser bar bush q. Pass the presser bar

ivBAS-311E.311EL.326E.326EL1★The following warning labels appear on the sewing machine.Please follow the instructions on the labels at all times when

42BAS-311E.311EL.326E.326ELChapter 3. Assembly6. Turn the pulley to align the needle bar with the shuttlehook. At this time, turn the stepping work c

43BAS-311E.311EL.326E.326ELChapter 3. Assembly9. Lower shaft mechanism (1)1. Tilt the machine head until it stops.2. Insert the rock gear shaft q from

44BAS-311E.311EL.326E.326ELChapter 3. Assembly10. Lower shaft (Rotary hook) (2)1. Fit the inner rotary hook in the large shuttle hook.2. Turn the pull

45BAS-311E.311EL.326E.326ELChapter 3. Assembly11. Thread trimmer mechanism1. Fit the hole of the thread trimmer connecting rod q over the pin of the c

46BAS-311E.311EL.326E.326ELChapter 3. Assembly12. Feed guide mechanism (Home position adjustment: X )311E, 311EL, and 326E1. Secure the large shuttle

47BAS-311E.311EL.326E.326ELChapter 3. Assembly12.Press the P key and adjust the X-sensor setting plate !7 so that the needle !4 is aligned with the ho

48BAS-311E.311EL.326E.326ELChapter 3. AssemblyFeed guide mechanism (Home position adjustment: Y )311E and 311EL1. Press the P key on the programmer, a

49BAS-311E.311EL.326E.326ELChapter 3. Assembly13. Covers 311E1. Secure XY-feed base covers (L) q and (R) w with thescrews e.2. Attach Y-feed bracket c

50BAS-311E.311EL.326E.326ELChapter 3. Assembly1. Attach the XY-feed bracket covers L q and R w using the screws.2. Insert the left and right feed brac

51BAS-311E.311EL.326E.326ELChapter 4. AdjustmentsChapter 4. Adjustments1. Adjusting the needle bar height adjustmentTurn the machine pulley to move th

BAS-311E.311EL.326E.326ELINDEXChapter 1. Mechanical description ... 11. Needle bar, thread

52BAS-311E.311EL.326E.326ELChapter 4. Adjustments3. Adjusting the needle clearance0.01 - 0.08mmqwqweqATurn the machine pulley to align the tip of the

53BAS-311E.311EL.326E.326ELChapter 4. Adjustments6. Adjusting the two-step work clamp lift amount¡The maximum work clamp lift amount is 25 ± 1 mm (for

54BAS-311E.311EL.326E.326ELChapter 4. Adjustments6-3. Adjustment of air pressure (for Pneumatic type 311E, 311EL, 326E,326EL)1. Air pressure should be

55BAS-311E.311EL.326E.326ELChapter 4. Adjustments7. Adjusting the movable knifeLoosen the nut e and move connecting rod lever r to the left or right t

56BAS-311E.311EL.326E.326ELChapter 4. Adjustments4. Fit the thread cutter connecting rod o on connecting le-ver pin !0, and install the needle plate w

57BAS-311E.311EL.326E.326ELChapter 4. Adjustments5. When installing the feed plate y, use a 2 mm- diameterpin !3 (such as a needle) to align the hole

58BAS-311E.311EL.326E.326ELChapter 4. Adjustments8. Adjusting the lowest point of the presser foot1. Turn the pulley to align the needle bar with the

59BAS-311E.311EL.326E.326ELChapter 4. Adjustments8-1. Presser foot adjustment1. Loosen the screw q, lower the presser foot w so that itsbottom can lig

60BAS-311E.311EL.326E.326ELChapter 4. Adjustments10. Wiper adjustment For vertical wiper (standard)1. When the thread wiper solenoid plunger q is dri

61BAS-311E.311EL.326E.326ELChapter 4. Adjustments11. Adjusting the home position1. Remove the needle and presser foot.2. Remove the flat screws w and

BAS-311E.311EL.326E.326EL3. Work clamp lifter mechanism ... 294. Feed

62BAS-311E.311EL.326E.326ELChapter 4. Adjustments (Y axis) 311E and 311EL1. Remove the belt cover q and the frame side cover w.2. Connect the program

63BAS-311E.311EL.326E.326ELChapter 4. Adjustments (Y axis) 326E, 326EL1. Press the P key and adjust the Y-sensor setting plate e so that the needle q

64BAS-311E.311EL.326E.326ELChapter 4. Adjustments12. Adjusting the tension of the timing belt Adjusting the tension of X-timing belt 311E1. Remove

65BAS-311E.311EL.326E.326ELChapter 4. Adjustments311EL and 326E, 326EL Adjusting the tension of X-timing belt A326X-timing belt A326 e is looped arou

66BAS-311E.311EL.326E.326ELChapter 4. Adjustments13. Adjusting backlashes Lower shaft1. Tilt the machine head until it stops.2. Loosen the set screw

67BAS-311E.311EL.326E.326ELChapter 4. Adjustments14. Adjusting the driving lever stopper position1. Remove the screws q and the top cover w.2. If thre

68BAS-311E.311EL.326E.326ELChapter 4. Adjustments16. Work clamp lift components for manual operation (Sole-noid type)1. Fully press in the plunger w o

69BAS-311E.311EL.326E.326ELChapter 4. Adjustments18. Adjusting the needle up stop positionrwyutqe1. Loosen the screw t (at the U side on the pulley q

70BAS-311E.311EL.326E.326ELChapter 5. How to make up the work clampChapter 5. How to make up the work clamp• The work clamp is available in two types;

71BAS-311E.311EL.326E.326ELChapter 5. How to make up the work clamp How to make up the plastic work clamp1. Cut out the plastic plate according to th

BAS-311E.311EL.326E.326ELChapter 5. How to make up the work clamp... 701. How to make up clamping type work c

72BAS-311E.311EL.326E.326ELChapter 5. How to make up the work clampCassette presser 1Lt=3.2SO2845-001SO2846-001Cassette presser 1RCassette presser 4Lt

73BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustmentChapter 6 Power supply and electrical partsadjustment1. Precautions

74BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment3. Fuse explanationWhen replacing a fuse, follow the instructions in

75BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment4. ConnectorsMost of the machine trouble is due to connector problem

76BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustmentPower supply circuit boardOutside of the panelPanel circuit boardP5D

77BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustmentProgrammer and programmer circuit boardProgrammer PCBProgrammer P -

78BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment• Home position is not properly detected.• Error [E.A1] appears.• Fo

79BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment3. Sewing operation• The work clamp does not operate.• (For BAS-311

80BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment• The machine motor does not run.• Motor operation is unstable.• Ne

81BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment• Error [E.40] appears.• Error [E.12] appears.• Emergency stop swi

1BAS-311E.311EL.326E.326ELChapter 1. Mechanical descriptionChapter 1. Mechanical description1. Needle bar, thread take-up, lower shaft and shuttle hoo

82BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment5. DIP switchesNote: When changing DIP switch setting the power must

83BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment DIP switch BB-1B-2B-3B-4B-5B-6B-7B-8When ONSingle split mode activ

84BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustmentDIP switches inside the control boxWait at least 5 minutes after tur

85BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment DIP switch DD-1D-2D-3D-4D-5D-6D-7D-8When ONThe first two stitche

86BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment6. Changing special functions using the memory switchesThe functions

87BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment Memory Switches (00 – 0F)memo-00memo-01memo-02memo-03memo-04memo-0

88BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustmentmemo-10memo-11memo-12memo-13memo-14memo-15memo-16memo-17memo-18memo-

89BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment[Set value]0: Sensor home position, 1: Center of sewing area, 2: Upp

90BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment7. Checking the input sensor and DIP switch input1. When the SPLIT N

91BAS-311E.311EL.326E.326ELChapter 6 Power supply and electrical parts adjustment8. Checking the input voltage1. Turn on the power switch.2. Press th