Brother DA-9280 Instruction Manual

DA-9280 THREE NEEDLE (TWIN NEEDLE) FEED OFF THE ARM DOUBLE CHAIN STITCHER English

4.㩷㪫㪘㪙㪣㪜㩷㪘㪥㪛㩷㪤㪦㪫㪦㪩㩷 DA-9280 34. TABLE AND MOTOR 4-1. Table processing diagram ࡮The top of the table should be 40 mm in thickness and should be strong

4.㩷㪫㪘㪙㪣㪜㩷㪘㪥㪛㩷㪤㪦㪫㪦㪩㩷 DA-9280 44-2. Motor CAUTION All cords should be secured at least 25 mm away from any moving parts. Furthermore, do not excessively

5. INSTALLATION 5 DA-92805. INSTALLATION CAUTION Machine installation should only be carried out by a qualified technician. Contact your Brother deal

5. INSTALLATION 6 DA-92803. Place the machine head on the table, adjust its position in forward and backward directions by aligning it with the hole

5. INSTALLATION 7 DA-92805-2. Ground wire connections Connect the ground wire to the sewing machine head and motor. * Use the correct type of ground

5. INSTALLATION 8 DA-92804. If the machine is being used with the puller attached, install the puller belt cover (8) with the two screws (9).

5. INSTALLATION 9 DA-92805-6. Lubrication CAUTION Be sure to wear protective goggles and gloves when handling the lubricating oil, so that it does no

5. INSTALLATION 10 DA-92806. Remove the rubber cap (10). 7. Turn the machine pulley until the needle bar (11) is raised to the highest position. 8.

6. PREPARATION BEFORE SEWING 11 DA-92806. PREPARATION BEFORE SEWING 6-1. Needles and threads The needle and threads to be used vary depending on sewi

6. PREPARATION BEFORE SEWING㩷 12 DA-92806-3. Threading the lower threads  CAUTION Turn off the power switch before threading the lower thread. Howev

DA-9280

7. SEWING 13 DA-92807. SEWING CAUTION Attach all safety devices before using the sewing machine. If the machine is used without these devices at

8. THREAD TENSION 14 DA-92808. THREAD TENSION 8-1. Adjusting the thread tension 1. Adjust the upper thread tension properly by turning th

8. THREAD TENSION㩷 15 DA-92808-3. Adjusting the stitch length CAUTION Turn off the power switch before adjusting the stitch length. However, th

8. THREAD TENSION 16 DA-9280The table below shows samples of stitches made with a highly elastic fabric and a fabric which is not so elastic. Adjust

9. CLEANING 17 DA-92809. CLEANING The following cleaning operations should be carried out each day in order to maintain the performance of this machi

10. STANDARD ADJUSTMENTS 18 DA-928010. STANDARD ADJUSTMENTS CAUTION Maintenance and inspection of the sewing machine should only be carried out

10. STANDARD ADJUSTMENTS㩷 DA-9280 19 10-2. Needle and looper timing adjustment Adjust so that the height of the needle is 0.2 - 0.8 mm lower when the

10. STANDARD ADJUSTMENTS 20 DA-928010-3. Timing of loopers running clear of needles The loopers (1) run in back of the needles (2) in their forward t

10. STANDARD ADJUSTMENTS㩷 DA-9280 21 10-4. Needle guard adjustment Adjust so that the needle (2) is pushed by the needle guard (3) and the clearance b

10. STANDARD ADJUSTMENTS 22 DA-928010-6. Tension release lever adjustment Adjust so that the center of the tension release lever (1) thread hole is 7

DA-9280 i Thank you very much for buying a BROTHER sewing machine. Before using your new machine, please read the safety instructions below and the ex

10. STANDARD ADJUSTMENTS㩷 DA-9280 23 10-9. Tension release shaft adjustment Adjust the tension release shaft so that the tension discs loosen when the

10. STANDARD ADJUSTMENTS 24 DA-928010-12. Puller height adjustment (Machines with puller) Adjust the height of the puller (1) so that it is 0.1 to 0.

11. INSTALLING OPTIONAL PARTS 25 DA-928011. INSTALLING OPTIONAL PARTS CAUTION Installation of optional parts should only be carried out by a qua

11. INSTALLING OPTIONAL PARTS㩷 26 DA-9280 4. Fill the thread cooler tank assembly (1) with the silicone oil (6). 5. Pass the thread throu

12. TROUBLESHOOTING 27 DA-928012. TROUBLESHOOTING x If there is a problem with operation, first check that the threads are correctly threaded and t

12. TROUBLESHOOTING 28 DA-9280 Problem Cause Remedy PageThe feed dog is too low. Adjust the feed dog height. 21 The presser foot pressure is too

ขᛒ⺑᣿ᦠ INSTRUCTION MANUAL Г᧲▐ᇨ̰ MANUAL DE INSTRUCCIONES Printed in Japan / ᇈኈڊׂ / Impreso en Japón http://www.brother.co.jp/ DA-9280SA9518-0

DA-9280 ii 2. Notes on safety CAUTION Environmental requirements Use the sewing machine in an area which is free from sources of strong electrical no

DA-9280 iii CAUTION Sewing This sewing machine should only be used by operators who have received the necessary training in safe use beforehand. The

DA-9280 iv 3. Warning labels ڎThe following warning labels appear on the sewing machine. Please follow the instructions on the labels at all times

DA-9280 CONTENTS 1. NAMES OF MAJOR PARTS ...1 2. MACHINE SPECIFICATIONS...2 3. OPTIONAL PARTS... 2 4. TABLE AND MOTOR ...

DA-9280 1.㩷NAMES OF MAJOR PARTS㩷1 1. NAMES OF MAJOR PARTS (1) Machine pulley (4) Needle bar (2) Front cover (5) Upper threa

DA-9280 2. MACHINE SPECIFICATIONS 3. OPTIONAL PARTS 22. MACHINE SPECIFICATIONS When sewing at a speed of 4,000 rpm, the needle thread coole