Brother BES-100E Instruction Manual Page 169
- Page / 186
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
BE-1204B-BC • BE-1206B-BC 9-5
Chapter 9 Error code list
Code Error Messages Error Measures
E-49
Can not identify the
machine model
Can not identify the machine
model
Turn OFF the power, check if the model
identification harness is connected properly, and
turn ON the power again.
E-4A
I/O CPU communication
error
Failed in the communication with
I/O CPU
Press the
or turn ON the F/B switch on the
head to either side. If the same error occurs
again, the connector of communication cable on
the I/O PCB may be disconnected.
E-A1 Main (Z) motor lock Spindle motor lock
Press the
or turn on the F/B switch on the
head to either side. If it occurs frequently, the
main shaft mechanism is faulty.
E-A2
Main (Z) PCB
temperature is too high
Main PC board temperature too
high
E-A3
Main (Z) motor voltage
is too low
Spindle motor voltage too low
E-A4
Main (Z) motor voltage
is too high
Spindle motor voltage too high
E-A5 Spindle CPU error Spindle motor CPU error
E-A6 ERROR A6
Spindle motor CPU communication
command error
E-A7 ERROR A7
Spindle motor CPU send/receive
error
This is not usually displayed.
E-A8 ERROR A8 Spindle stop position signal error
Adjust the pulley stop position (100 °) above the
needle and press the
. If the error occurs
frequently, the parts related to the main shaft stop
position sensor are faulty.
E-A9
Spindle CPU parameter
error
Spindle CPU parameter error
E-B0 Lower shaft CPU error Lower shaft CPU error
E-B1
Thread jammed in
rotary hook
Thread tangle in rotary hook
E-B2
Hook motor origin point
error
Hook motor origin point error
E-B3
Hook motor standby
position error
Hook motor standby position error
E-B4
Hook motor standby
position error
Hook motor motor mode error
E-B5
Hook motor
communication error
Hook motor communication error
E-B6
Hook motor parameter
error
Hook motor parameter error
E-B7
Hook motor overheat
error
Hook motor overheat error
E-B8
Hook motor overcurrent
error Turn off the
power
Hook motor overcurrent error
This is not displayed in this model.
E-B9
Thread trimming motor
origin point error
Thread trimming motor zero point
error
Turn the power off and on once. If the same
error occurs again, the lower shaft motor is faulty.
E-BA
Power supply frequency
error
Power supply frequency error
Turn the power off and check the thread trimmer
and turn the power on again. If it occurs again,
the thread trimmer is faulty.
E-BC No power error No power error
It may usually occur momentarily when turning off
the machine. If it occurs when the machine is
on, it is a power failure detection error.
- BE-1204B-BC 1
- BE-1206B-BC 1
- SAFETY INSTRUCTIONS 3
- 2 Notes on safety 4
- Installation 5
- Cleaning 5
- Maintenance and inspection 6
- 3 Warning labels 7
- 6 BE-1204B-BC • BE-1206B-BC 8
- Before Starting Operation 10
- BE-1204B-BC • BE-1206B-BC 9 11
- Explanation of models 12
- Configuration of this manual 12
- BE-1204B-BC • BE-1206B-BC 11 13
- Screen Composition 14
- BE-1204B-BC • BE-1206B-BC 13 15
- Contents 16
- Chapter 8 Adjustment 19
- Chapter 10 Troubleshooting 19
- 18 BE-1204B-BC • BE-1206B-BC 20
- Chapter 1 21
- 1. Specifications 22
- Accessories 23
- 3. Installation 25
- ! When using a crane 26
- 3-2 Installation of Machine 27
- 1-8 BE-1204B-BC • BE-1206B-BC 28
- 3-4 Mounting of Table 29
- 3-5 Mounting of Cotton Stand 32
- 3-7 Grounding 34
- 4-1 Upper Threading 35
- The cotton stand (top view) 36
- Pass a thread in the order 36
- 4-2 Replacement of Bobbin 37
- Attaching the holder base 42
- W1248Q W1249Q 44
- Embroidering Procedures 47
- Chapter 2 47
- Functions of Operation Panel 48
- BE-1204B-BC • BE-1206B-BC 2-3 49
- Operation panel 50
- Switches at Machine Heads 51
- BE-1204B-BC • BE-1206B-BC 2-7 53
- Turn on the Machine Power 54
- Retrieve the Embroidery Data 55
- Start Embroidering 55
- Chapter 3 57
- What Can the Machine Do? 58
- Selection of Data 59
- 3-4 BE-1204B-BC • BE-1206B-BC 60
- Eject switch 60
- Pressing 61
- then press 62
- Reading from Memory 63
- BE-1204B-BC • BE-1206B-BC 3-9 65
- Currently displayed screen 65
- No. of screens to be selected 65
- Delete all embroidery data 66
- Reset settings 66
- Tape Reader Input Setting 67
- 6. Press 68
- "T" is input 70
- "E" is input 70
- "S" is input 70
- "N" is deleted 72
- "O" is input 72
- Sewing Operation 73
- Sewing is interrupted 74
- once again 74
- Step Forward and Step-Back 75
- For Step Forward (Back) 76
- Resuming Sewing 76
- Writing the embroidering data 77
- 9. Press the button 78
- Chapter 4 79
- Editing of Embroidering Data 79
- Rotation 81
- Enlargement and Reduction 82
- is reversed in black 83
- 4-6 BE-1204B-BC • BE-1206B-BC 84
- Right/left mirror patter 84
- Up/down mirror patter 84
- BE-1204B-BC • BE-1206B-BC 4-7 85
- Repetition 86
- BE-1204B-BC • BE-1206B-BC 4-9 87
- Other Editing 88
- Chapter 5 Setting 91
- BE-1204B-BC • BE-1206B-BC 5-3 93
- Setting of Needle Bars 94
- 4. Press 95
- Thread Breakage Sensor 96
- Automatic Step-Back 97
- 5-8 BE-1204B-BC • BE-1206B-BC 98
- Number of stitches 98
- Setting of Machine 99
- Speed Range 100
- Speed of Each Speed Range 101
- Setting of Mending 102
- Modify this figure 103
- Thread Trimming Length 104
- Thread Withdrawal Feed Length 105
- Chapter 5 Setting 106
- Sewing Area 107
- Hoop Retract Point 108
- Hoop Automatic Retract 109
- Setting of Environment 110
- Checking the Embroidery Area 111
- Checking with the rectangle 112
- Checking with the octagon 112
- Display Language 114
- Alarm Sound 115
- Motive Speed 116
- Small-Pitch Deletion 117
- Automatic pause insertion 118
- Lock Stitch 119
- Validating the lock stitch 120
- Invalidating the lock stitch 120
- Speed Limit in a Short Pitch 122
- Feed Timing 123
- Automatic Input Setting 124
- Display of Information 127
- Features of Machine 128
- Information about Versions 129
- 1. Operating Procedures 132
- 2. Machine Stop 133
- 3-1 Remedies 134
- 3-2 Mending 135
- W1275Q W1276Q 136
- 5. Hoop Feed Position 138
- 6. Area Check 139
- 7. Jog Switches 140
- W1283Q W1282Q 141
- Chapter 7 Maintenance 143
- CAUTION 144
- 1. Cleaning 144
- 1-2 Cleaning of Needle Plate 145
- 2. Oiling 146
- 2-2 Lower shaft 147
- 3. Greasing 148
- Chapter 7 Maintenance 149
- 3-2 Lower gear 150
- 3-3 Driving shaft 150
- 3. Attach the head cover R 151
- 3-5 Feed Guide Section 152
- Chapter 8 Adjustment 153
- BE-1204B-BC • BE-1206B-BC 8-3 155
- Chapter 8 Adjustment 156
- BE-1204B-BC • BE-1206B-BC 8-5 157
- BE-1204B-BC • BE-1206B-BC 8-7 159
- 8-8 BE-1204B-BC • BE-1206B-BC 160
- 4-1 Attaching the Fixed Knife 161
- 5. Thread Wiper Adjustment 164
- Chapter 9 Error code list 165
- Chapter 9 Error code list 166
- Chapter 10 Troubleshooting 173
- Mechanical Section 174
- Chapter 10 Troubleshooting 175
- Electrical Section 176
- Chapter 11 181
- Optional Equipment 181
- 1. Attaching Bobbin Winder 182
- INSTRUCTION MANUAL 186
Related products and manuals for Sewing machines Brother BES-100E
(68 pages)
Sewing machines Brother LS-2720 User Manual
(15 pages)
(15 pages)
Sewing machines Brother BAS-342E User Manual
(10 pages)
(10 pages)
Sewing machines Brother BES-941BC User Manual
(270 pages)
(270 pages)
© 2020, manymanuals.com. All rights reserved. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals