Brother BES-100E Instruction Manual Page 177
- Page / 186
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
BE-1204B-BC • BE-1206B-BC 10-5
Chapter 10 Troubleshooting
Symptom Measures
The needle bar case lock error
occurs.
• Is the INDEX motor rotating?
→ If not, refer to the block diagram showing the cable connections and
check to see if connection from the INDEX motor to the main PCB
is proper.
Check the resistance values of pins 1 and 3 and pins 4 and 6 at the
connector section of the INDEX motor. The normal resistance
value is approximately 6.6Ω.
→ If it is not normal, replace the INDEX motor with a new one. Also
replace the drive PCB with a new one.
• Manually turn the color change pulley.
→ If it is abnormally heavy, adjust the color change mechanism and
the needle cap case.
• Replace the needle bar position sensor (potentiometer) with a new
one.
• Replace the I/O PCB 0 with a new one.
X-axis or Y-axis home position
detection error occurs.
• Was the XY carriage moving?
→ If so, refer to the block diagram showing the cable connections and
check to see if connection from the X and Y area sensor to the drive
PCB is proper.
• Was the XY motor rotating?
→ If so, check the XY carriage mechanism.
• If the XY motor is not rotating, refer to the cable connection block
diagram and check to see if connection from the XY motor to the drive
PCB is proper.
The thread breakage error frequently
occurs although thread is not broken.
• Enter the CASE test mode and turn the thread breakage sensor pulley
corresponding to each needle bar of the head with which this error
occurs while switching the needle bar from number 1 in ascending
order and check to see that the red LED on the head blinks.
→ If there is no problem, lower the thread breakage sensitivity value of
the machine controller. (The standard value is 0.)
• Check connection from the thread breakage sensor PCB to the thread
tension base PCB if it does not blink.
• Replace the thread breakage sensor PCB with a new one.
The X-axis motor connector
connection error occurs.
• Refer to the block diagram showing the cable connections and check
the connection from the two X motors (one X motors in four head
models) on the left and right to the main PCB.
The main shaft motor lock error
occurs.
• Enter the encoder signal mode and manually turn the main shaft pulley.
→ If it is abnormally heavy, the main shaft mechanism is faulty.
• Does the main shaft motor rotate at all when the error occurs?
→ If it does not rotate at all, check fuse F1 and F2 on the power supply
PCB in the control box. Refer to the block diagram showing the
cable connections and check to see if connection from the main
shaft motor to the drive PCB is proper.
• Manually turn the main shaft pulley in the encoder signal test mode
and check to see if the stop position signal and encoder signal are
proper.
→ If either of the signals does not change, refer to the block diagram
showing the cable connections and check to see if connection from
the encoder and stop position sensor to the power supply PCB is
proper.
- BE-1204B-BC 1
- BE-1206B-BC 1
- SAFETY INSTRUCTIONS 3
- 2 Notes on safety 4
- Installation 5
- Cleaning 5
- Maintenance and inspection 6
- 3 Warning labels 7
- 6 BE-1204B-BC • BE-1206B-BC 8
- Before Starting Operation 10
- BE-1204B-BC • BE-1206B-BC 9 11
- Explanation of models 12
- Configuration of this manual 12
- BE-1204B-BC • BE-1206B-BC 11 13
- Screen Composition 14
- BE-1204B-BC • BE-1206B-BC 13 15
- Contents 16
- Chapter 8 Adjustment 19
- Chapter 10 Troubleshooting 19
- 18 BE-1204B-BC • BE-1206B-BC 20
- Chapter 1 21
- 1. Specifications 22
- Accessories 23
- 3. Installation 25
- ! When using a crane 26
- 3-2 Installation of Machine 27
- 1-8 BE-1204B-BC • BE-1206B-BC 28
- 3-4 Mounting of Table 29
- 3-5 Mounting of Cotton Stand 32
- 3-7 Grounding 34
- 4-1 Upper Threading 35
- The cotton stand (top view) 36
- Pass a thread in the order 36
- 4-2 Replacement of Bobbin 37
- Attaching the holder base 42
- W1248Q W1249Q 44
- Embroidering Procedures 47
- Chapter 2 47
- Functions of Operation Panel 48
- BE-1204B-BC • BE-1206B-BC 2-3 49
- Operation panel 50
- Switches at Machine Heads 51
- BE-1204B-BC • BE-1206B-BC 2-7 53
- Turn on the Machine Power 54
- Retrieve the Embroidery Data 55
- Start Embroidering 55
- Chapter 3 57
- What Can the Machine Do? 58
- Selection of Data 59
- 3-4 BE-1204B-BC • BE-1206B-BC 60
- Eject switch 60
- Pressing 61
- then press 62
- Reading from Memory 63
- BE-1204B-BC • BE-1206B-BC 3-9 65
- Currently displayed screen 65
- No. of screens to be selected 65
- Delete all embroidery data 66
- Reset settings 66
- Tape Reader Input Setting 67
- 6. Press 68
- "T" is input 70
- "E" is input 70
- "S" is input 70
- "N" is deleted 72
- "O" is input 72
- Sewing Operation 73
- Sewing is interrupted 74
- once again 74
- Step Forward and Step-Back 75
- For Step Forward (Back) 76
- Resuming Sewing 76
- Writing the embroidering data 77
- 9. Press the button 78
- Chapter 4 79
- Editing of Embroidering Data 79
- Rotation 81
- Enlargement and Reduction 82
- is reversed in black 83
- 4-6 BE-1204B-BC • BE-1206B-BC 84
- Right/left mirror patter 84
- Up/down mirror patter 84
- BE-1204B-BC • BE-1206B-BC 4-7 85
- Repetition 86
- BE-1204B-BC • BE-1206B-BC 4-9 87
- Other Editing 88
- Chapter 5 Setting 91
- BE-1204B-BC • BE-1206B-BC 5-3 93
- Setting of Needle Bars 94
- 4. Press 95
- Thread Breakage Sensor 96
- Automatic Step-Back 97
- 5-8 BE-1204B-BC • BE-1206B-BC 98
- Number of stitches 98
- Setting of Machine 99
- Speed Range 100
- Speed of Each Speed Range 101
- Setting of Mending 102
- Modify this figure 103
- Thread Trimming Length 104
- Thread Withdrawal Feed Length 105
- Chapter 5 Setting 106
- Sewing Area 107
- Hoop Retract Point 108
- Hoop Automatic Retract 109
- Setting of Environment 110
- Checking the Embroidery Area 111
- Checking with the rectangle 112
- Checking with the octagon 112
- Display Language 114
- Alarm Sound 115
- Motive Speed 116
- Small-Pitch Deletion 117
- Automatic pause insertion 118
- Lock Stitch 119
- Validating the lock stitch 120
- Invalidating the lock stitch 120
- Speed Limit in a Short Pitch 122
- Feed Timing 123
- Automatic Input Setting 124
- Display of Information 127
- Features of Machine 128
- Information about Versions 129
- 1. Operating Procedures 132
- 2. Machine Stop 133
- 3-1 Remedies 134
- 3-2 Mending 135
- W1275Q W1276Q 136
- 5. Hoop Feed Position 138
- 6. Area Check 139
- 7. Jog Switches 140
- W1283Q W1282Q 141
- Chapter 7 Maintenance 143
- CAUTION 144
- 1. Cleaning 144
- 1-2 Cleaning of Needle Plate 145
- 2. Oiling 146
- 2-2 Lower shaft 147
- 3. Greasing 148
- Chapter 7 Maintenance 149
- 3-2 Lower gear 150
- 3-3 Driving shaft 150
- 3. Attach the head cover R 151
- 3-5 Feed Guide Section 152
- Chapter 8 Adjustment 153
- BE-1204B-BC • BE-1206B-BC 8-3 155
- Chapter 8 Adjustment 156
- BE-1204B-BC • BE-1206B-BC 8-5 157
- BE-1204B-BC • BE-1206B-BC 8-7 159
- 8-8 BE-1204B-BC • BE-1206B-BC 160
- 4-1 Attaching the Fixed Knife 161
- 5. Thread Wiper Adjustment 164
- Chapter 9 Error code list 165
- Chapter 9 Error code list 166
- Chapter 10 Troubleshooting 173
- Mechanical Section 174
- Chapter 10 Troubleshooting 175
- Electrical Section 176
- Chapter 11 181
- Optional Equipment 181
- 1. Attaching Bobbin Winder 182
- INSTRUCTION MANUAL 186
Related products and manuals for Sewing machines Brother BES-100E
(68 pages)
Sewing machines Brother LS-2720 User Manual
(15 pages)
(15 pages)
Sewing machines Brother BAS-342E User Manual
(10 pages)
(10 pages)
Sewing machines Brother BES-941BC User Manual
(270 pages)
(270 pages)
© 2020, manymanuals.com. All rights reserved. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals