Brother XE5427-001 User Manual Page 81
- Page / 92
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Troubleshooting 79
3
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
The upper thread
breaks.
There are knots or tangles in the
thread.
Remove any knots or tangles.
-
The upper thread tension is too
tight.
Loosen the upper thread tension. page 63
The thread is tangled, for example,
in the bobbin case.
Remove the tangled thread. If the
thread is tangled in the bobbin case,
clean the race.
page 74
The needle is bent or blunt. Replace the needle.
page 28
The needle is incorrectly installed. Correctly install the needle.
The area around the hole in the
embroidery foot is scratched, or
has a burr on it.
Replace the embroidery foot.
Contact your dealer or the nearest
authorized service center.
-
The bobbin case is scratched, or
has a burr on it.
Replace the bobbin case.
Contact your dealer or the nearest
authorized service center.
-
A bobbin designed specifically for
this machine is not used.
Incorrect bobbins will not work
properly. Only use a bobbin
designed specifically for this
machine.
page 29
Bobbin thread
does not wind
neatly on the
bobbin.
The thread is not passed through
the bobbin-winding thread guide
correctly.
Correctly pass the thread through the
bobbin-winding thread guide.
page 31
The thread that was pulled out
was not wound onto the bobbin
correctly.
Wind the thread that was pulled off
around the bobbin five or six times
clockwise.
page 32
The lower thread is
tangled or breaks.
The bobbin thread is incorrectly
installed.
Correctly install the bobbin thread. page 34
The bobbin is scratched or does
not rotate smoothly, or has a burr
on it.
Replace the bobbin.
-
The thread is tangled.
Remove the tangled thread and clean
the race.
page 74
A bobbin designed specifically for
this machine is not used.
Incorrect bobbins will not work
properly. Only use a bobbin
designed specifically for this
machine.
page 29
The thread is
tangled on the
wrong side of the
fabric.
The upper thread was not
threaded correctly.
Correct the upper threading. page 38
The thread tension
is incorrect.
The upper thread was not
threaded correctly.
Correct the upper threading.
Make sure that the thread is hanged
on the thread guide spring which is
on the left side of the thread guide
cover.
page 38,
page 39
The bobbin thread is incorrectly
installed.
Correctly install the bobbin thread. page 34
Symptom Probable Cause Remedy Reference
appendix1 Page 79 Monday, August 18, 2008 8:08 PM
- Operation Manual 1
- Introduction 3
- Important Safety Instructions 3
- SAVE THESE INSTRUCTIONS 4
- IMPORTANT 5
- Contents 7
- APPENDIX 73 8
- Machine Features 9
- Accessories 10
- Optional accessories 11
- Front view 12
- Needle and embroidery foot 13
- Right-side/rear view 13
- Operation buttons 14
- Operation panel 15
- 1 GETTING READY 17
- Basic Steps for Embroidering 18
- Turning the Machine On/Off 19
- Turning on the machine 20
- Turning off the machine 20
- Attaching the Embroidery Unit 21
- Removing the embroidery unit 23
- Viewing the LCD 24
- Checking machine operating 27
- Preparing the Needle 29
- Replacing the needle 30
- Winding/Installing the Bobbin 31
- Installing the bobbin 36
- Upper Threading 39
- Threading the upper thread 40
- Preparing the Fabric 45
- Setting the fabric in the 46
- Preparing the Fabric 45 47
- Removing the embroidery 50
- 2EMBROIDERY 51
- Selecting Embroidery Patterns 52
- Setting for embroidering 53
- Selecting alphanumeric 55
- Selecting a frame pattern 57
- Using an embroidery card 57
- Embroidering 59
- Appliquéing 61
- Editing and Saving Patterns 63
- Adjusting the upper thread 65
- Adjusting the bobbin thread 66
- Connecting character patterns 67
- Resewing 68
- Thread runs out partway 69
- Stopping while embroidering 69
- Using the Memory Function 71
- Saving patterns 72
- Retrieving embroidery 73
- 3 APPENDIX 75
- Care and Maintenance 76
- Troubleshooting 80
- Troubleshooting 79 81
- Troubleshooting 81 83
- Error messages 84
- Troubleshooting 83 85
- Error Message Probable Cause 85
- Adjusting the LCD 87
- Operation beep 87
Related products and manuals for Sewing machines Brother XE5427-001
Sewing machines Brother V61 User Manual
(100 pages)
(100 pages)
Sewing machines Brother HE-800A User Manual
(118 pages)
(118 pages)
Sewing machines Brother PR-600II User Manual
(28 pages)
(28 pages)
(24 pages)
Sewing machines Brother NC21SE User Manual
(66 pages)
(66 pages)
Sewing machines Brother CS 80 User Manual
(115 pages)
(115 pages)
Sewing machines Brother HE 120 User Manual
(183 pages)
(183 pages)
Sewing machines Brother XL-6040 User Manual
(101 pages)
(101 pages)
Sewing machines Brother 885-X06 User Manual
(104 pages)
(104 pages)
Sewing machines Brother CS-8060 User Manual
(116 pages)
(116 pages)
Sewing machines Brother PC 3000 User Manual
(104 pages)
(104 pages)
Sewing machines Brother CS-770 User Manual
(68 pages)
(68 pages)
Sewing machines Brother CS 100T User Manual
(67 pages)
(67 pages)
Sewing machines Brother XL5100 User Manual
(85 pages)
(85 pages)
© 2020, manymanuals.com. All rights reserved. | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals