Brother RH-9820 Service Manual Page 228
- Page / 236
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
9. ERROR CODES
RH-9820
219
9. ERROR CODES
DANGER
Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet before
opening the cover of the control box. Touching areas where high voltages are present can result in severe injury.
If a problem should occur with the sewing machine, the buzzer will sound and an error code and error message will appear in
the display.
Follow the remedy procedure to eliminate the cause of the problem.
Switch-related errors
Code Cause Remedy Page
E010 Stop switch was pressed during standby. Remove your finger from the stop switch (so that it is off).
*
1
E011 Stop switch was pressed during sewing.
Press the RESET key to clear the error.
* Press the key to move the feed mechanism so that
you can continue sewing.
*
1
E015
The stop switch was still being pressed, or
there is a problem with the stop switch
connection.
Turn off the power, and check the stop switch if it was not
being pressed at the time.
-
E016 Problem with the stop switch connection.
Turn off the power and check the connection of the stop
switch connector P13 at the main P.C. board.
200
E024 Start switch is being pressed. Release the start switch (so that it turns off).
*
1
E025
Start switch was depressed after the power
was turned on, or connection of start switch is
defective.
Turn off the power and check if the start switch is pressed.
If the start switch is not being pressed, check the switch
connector P6 at the main P.C. board.
200
E034 Work clamp switch is being pressed. Release the work clamp switch (so that it turns off).
*
1
E035
Work clamp switch was depressed, or
connection of work clamp switch is defective.
Turn off the power and check the work clamp switch.
*
1
E050
Machine head tilting was detected after the
power was turned on.
Turn off the power, and then return the machine head to
its original position.
Check the connection of the machine head safety switch
connector P9 at the main P.C. board.
200
E051
Machine head tilting was detected while the
sewing machine was operating.
Turn off the power, and then return the machine head to
its original position.
Check the connection of the machine head safety switch
connector P9 at the main P.C. board.
200
E055
Machine head tilting was detected when the
power was turned on.
Turn off the power, and then return the machine head to
its original position.
Check the connection of the machine head safety switch
connector P9 at the main P.C. board.
200
E065
An operation panel key was still being pressed
when the power was turned on, or key is faulty.
Turn off the power and check that no keys are being
pressed.
-
*
1
：Refer to the reference page in “10. ERROR CODES” in the instruction manual.
0320B
0461B
- RH-9820 1
- SAFETY INSTRUCTIONS 3
- DANGER 4
- CAUTION 4
- [3] Warning labels 6
- Belt cover 7
- CONTENTS 8
- 1. MACHINE SPECIFICATIONS 10
- 2. FUNCTION SETTINGS 11
- 0708B 0709B 12
- 2-6. Input checking method 24
- 2-7. Output checking method 27
- 3. READING/WRITING DATA 31
- 3-3. Data read/write mode 32
- 4. MECHANICAL DESCRIPTIONS 35
- 4-4. Feed mechanism 38
- 4-5. Presser foot mechanism 39
- 4-6. Cloth opening mechanism 40
- 4-7. Cutter mechanism 41
- 4-8. Looper mechanism 41
- 4-9. Spreader mechanism 42
- <-01> 44
- <-02> 45
- 5. DISASSEMBLY 47
- 5-3. Feed mechanism 50
- 5-3-2. X feed unit 51
- 5-3-3. Y feed unit 51
- 5-5. Spreader mechanism 53
- 5-6. Looper mechanism 54
- 5-8. Looper base mechanism 56
- 5-9. Needle bar mechanism 57
- 5-10. Lubrication 58
- 5-12. Upper shaft mechanism 61
- 5-13. Cutter mechanism 62
- 6. ASSEMBLY 63
- 6-1. Cutter mechanism 64
- B Assemble as shown in the 65
- D Insert the cutter arm pin 65
- 6-3. Zigzag mechanism 68
- Insert into the groove 69
- C Assemble as shown in the 79
- D Place the pulse motor Y 79
- E Belt tension adjustment 80
- (Viewed from the left) 84
- (Viewed from the front) 84
- Measurement 91
- 6-10. Lower shaft mechanism 94
- Should be no clearance 98
- 6-11. Looper mechanism 99
- (Clearance) 100
- (Viewed from underneath) 100
- 6-12. Spreader mechanism 101
- (When at 103
- Clearance： 103
- 6-14. Threading mechanism 104
- 6-15-1. Feed base 106
- (When at maximum retraction) 111
- 6-15-2. X feed shaft holder 113
- (Viewed from directly to 114
- (Viewed from the side) 114
- Base of 114
- 6-16. X feed mechanism 116
- A Assemble as shown in the 117
- Measurement position 121
- 6-19. Covers 124
- <-01 specifications> 130
- A Spring hook installation 132
- <-02 specifications> 134
- F Spring hook installation 135
- (When cylinder is at 137
- 6-23. Routing the harnesses 138
- 6-24. Routing the air tubes 140
- E Inserting the wicks 146
- Maintain a 147
- 7. ADJUSTMENTS 150
- Looper height 151
- 0487B 0488B 155
- Moves to left 156
- Moves to right 156
- 0.01 - 0.08mm 158
- CAUTION 166
- (When using a 173
- 2-pedal foot switch) 173
- 0.3 mm 181
- 184
- Needle plate 186
- value will not be changed 198
- 6. Press the TEST key (6) 200
- 8. ELECTRICAL MECHANISM 206
- 1199B 0692B 207
- 8-3. Description of fuses 208
- 8-4-1. Connector positions 209
- 8-5. Troubleshooting 215
- 8-5-2. Diagnosis flowchart 216
- 8-5-3. Remedy 219
- 9. ERROR CODES 228
- 10. TROUBLESHOOTING 234
- SERVICE MANUAL 236
Related products and manuals for Sewing machines Brother RH-9820
Sewing machines Brother BAS-342F User Manual
(24 pages)
(24 pages)
Sewing machines Brother 885-V12 User Manual
(93 pages)
(93 pages)
Sewing machines Brother PC-2800 Owner's Manual
(150 pages)
(150 pages)
Sewing machines Brother 885-X01 User Manual
(44 pages)
(44 pages)
Sewing machines Brother 885-V55 User Manual
(96 pages)
(96 pages)
(42 pages)
(77 pages)
Sewing machines Brother LS-2000 User Manual
(17 pages)
(17 pages)
Sewing machines Brother HS-3000 User Manual
(21 pages)
(21 pages)
Sewing machines Brother Z-8550A Service Manual
(128 pages)
(128 pages)
© 2020, manymanuals.com. All rights reserved. | 0.756 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals