Brother BAS-761 Service Manual Page 163
- Page / 179
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
7. FOLDING MACHINE
BAS-7610
7-33
22. The seam margin is large.
<Cause>
A. Because the forward part of the center blade is curved up, the clearance between the needle plate
and the center blade is large only at the forward part.
Remove the center blade. Distort the center blade to level.
B. The inner clamp blades are improperly attached.
Refer to “Trouble 6. Cause A”.
C. Because the center blade assembly is attached too far forward, the pocket material is improperly
folded.
After loosening the eight bolts (1), shift the center blade backward in the loose holes of the connecting blocks
(center blade), then fasten the bolts (1).
At this time, the inner clamp assembly and the folding clamp assembly might need to be shifted backward
simultaneously.
In this case, loosen the four screws (2) and the two plate springs are taken out to the front.
(Only the part which shifted the whole center blade to the back)
D. The tucking blades have burrs.
Remove the burrs and buff the tucking blades.
E. Program defect
Reprogram partially.
Connecting pin
Connecting block
Plate spring R 0.8
Center blade 3-corner J
Bolt 4X20
Plate spring L 0.8
Center blade assembly
1789S
Connecting pin
Connectin
g
block
Bolt 5X25
Inner clamp 3-corner J
Inner clamp U 1
Folding plate supporter
Folding plate
supporter
Folding plate
supporter
Inner clam
p
U 2
Folding plate
supporter
Inner clamp U 3
Inner clam
p
U 3
Inner clamp assembly
1790S
Connecting block SR assembly
Bolt 5X25
Folding clamp 3-corner J
Connecting block SL assembly
Bolt 4X8
Adjusting screw
Settin
g
p
late
Tucking blade R-3J
Tucking blade L-3J
Tucking blade LD-3J
Tucking blade RD-3J
Chamfering blade RJ
Chamferin
g
blade LJ
1792S
Folding clamp assembly
- SAFETY INSTRUCTIONS 2
- CAUTION 3
- 3. Warning labels 5
- 1-3. Needle zigzag mechanism 10
- 1-4. Lubrication mechanism 12
- 1-5. Thread trimmer 14
- 1-6. Presser bar lifter 16
- 1-7. Stacker 16
- 1-8. Feed guide mechanism 17
- 1-9. Folding mechanism 18
- 1. MECHANICAL DESCRIPTIONS 19
- 1-11. Bobbin winder mechanism 20
- 2-1. Basic operation 21
- <Starting> 22
- <Removing stacker> 23
- <Removing folding base> 24
- 3. DISASSEMBLY 25
- 3-2. Presser foot mechanism 26
- 3-5. Needle bar 28
- 3-6. Motor 29
- 3-7. Timing belt 29
- 3-8. Auxiliary shaft 30
- 3-9. Zigzag 31
- 4. ASSEMBLY 33
- 4-2. Auxiliary shaft 34
- 4-3. Timing belt 34
- 4-4. Motor 35
- 4-5. Needle bar 36
- 4-8. Presser foot mechanism 38
- 4-9. Cover 39
- 5. ADJUSTMENT 41
- X2.4 rotary hook : 2.4 mm 46
- X1.7 rotary hook : 1.8 mm 46
- X2.4 rotary hook : 1.2 mm 46
- 5-4. Tension release 49
- 5-5. Thread tension 49
- <Thread guide, R> 50
- <Fixed knife> 51
- <Needle> 51
- 5-11-1. Folding clamp 56
- 5-11-2. Inner clamp 56
- 5-11-3. Center blade 56
- 5-11-4. Sewing clamp 57
- 5-11-9. Stacker wiper 59
- 5-11-10.Stacker bar inside 59
- 5-11-11. Stacker bar outside 59
- 5-11-12. Stacker roller 60
- 5-30-2. Setting of MODE 73
- <Operation panel> 76
- <Programmer> 76
- 6-3. Power supply 77
- 6-4. PROM 80
- 6-5. Connector 81
- P3 [TRIM] (MOLEX 5273-02A) 82
- P4 [POWER] (MOLEX 5566-10A) 82
- P7 [FDD] (3 M 3431-6002SCFL) 84
- P23 [CLAMP] (MOLEX 5045-03A) 88
- 6-5-2. Power supply PCB 91
- P1 [MAIN] (MOLEX 5277- 04A) 91
- P4 [AC-IN] (MOLEX 5277 - 06A) 91
- 6-5-3. Operation panel PCB 92
- 6-5-4. Programmer PCB 94
- P2 [MAIN] (MOLEX 5268-12A) 94
- 6-5-5. Pattern sensor PCB 95
- 6-6. Sensor 96
- 6-6-2. Function of sensor 97
- < Jig pattern sensor > 99
- < Cylinder sensor > 100
- < Clamp-in sensor > 101
- BAS-7610 102
- 6-7. Harness 103
- 6-8. Servo amplifier 115
- < Servo motor > 116
- 6-9. DIP switches 119
- 6-10. Error code 121
- 6-11. Exchange of PCB 125
- 6.ELECTRIC COMPONENTS 126
- 6. ELECTRIC COMPONENTS 127
- 7. FOLDING MACHINE 131
- 7-2. Valve 133
- 7-4. Adjustment 136
- Tucking blade R-3J 138
- Tucking blade L-3J 138
- Tucking blade LD-3J 138
- Tucking blade RD-3J 138
- D. Program defect 139
- C. Program defect 140
- B. Program defect 142
- E. Program defect 148
- D. Program defect 149
- A. The flap margin is small 153
- A. The flap margin is small 156
- A. The flap margin is large 157
- 21. The pocket top is narrow 162
- 22. The seam margin is large 163
- <Cause> 168
- Tucking blade D 172
- Tucking blade RDD or LDD 172
- 1 - 2 mm 172
- Tucking blade RD 172
- 4. The base is curved 173
- 8. The corners are round 177
Related products and manuals for Sewing machines Brother BAS-761
(91 pages)
(2 pages)
Sewing machines Brother 681B-UG User Manual
(39 pages)
(39 pages)
(68 pages)
Sewing machines Brother LS-2720 User Manual
(15 pages)
(15 pages)
© 2020, manymanuals.com. All rights reserved. | 2.170 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals