Brother BAS-761 Service Manual Page 59
- Page / 179
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5. ADJUSTMENT
BAS-7610
5-19
5-11-9. Stacker wiper
Activate air compression. Turn off the power.
Valve Action by manual button Setting of the speed controller
Move toward you
(Manual button side)
19 Wiper---Move
Move away from you
Make the operating speed as fast as possible without
operating jostling of the stacker wiper.
Cylinder Setting of the air cushion
Rod side
Turn the screw all the way but tighten lightly. Next,
loosen the screw 1.5 turns. Fix the screw with the
nut.
End side
Turn the screw all the way but tighten lightly. Next,
loosen the screw 1.5 turns. Fix the screw with the
nut.
5-11-10.Stacker bar inside
Activate air compression. Turn off the power.
Valve Action by manual button Setting of the speed controller
Move toward you
(Manual button side)
Adjust the speed to follow the stacker bar without jolting.20 Bar---Move
Move away from you Adjust low enough so as not to interfere with the cloth to be
sewn next.
Cylinder Setting of air cushion
End side,
Rod side
Turn the screw all the way but tighten lightly.
Next, loosen the screw 1.5 turns. Fix the screw
with the nut.
5-11-11. Stacker bar outside
Activate air compression. Turn off the power.
Valve Action by manual button Setting of the speed controller
Move toward you
(Manual button side)
Make the operating speed as fast as possible without
operating jostling of the stacker bar.
21 Bar---Move
Move away from you Adjust the bar speed to allow movement at a highest
possible speed where no abnormal sounds.
Cylinder Setting of air cushion
End side,
Rod side
Turn the screw all the way but tighten lightly. Next,
loosen the screw 1.5 turns. Fix the screw with the nut.
1365S
1372S
1373S
1374S
- SAFETY INSTRUCTIONS 2
- CAUTION 3
- 3. Warning labels 5
- 1-3. Needle zigzag mechanism 10
- 1-4. Lubrication mechanism 12
- 1-5. Thread trimmer 14
- 1-6. Presser bar lifter 16
- 1-7. Stacker 16
- 1-8. Feed guide mechanism 17
- 1-9. Folding mechanism 18
- 1. MECHANICAL DESCRIPTIONS 19
- 1-11. Bobbin winder mechanism 20
- 2-1. Basic operation 21
- <Starting> 22
- <Removing stacker> 23
- <Removing folding base> 24
- 3. DISASSEMBLY 25
- 3-2. Presser foot mechanism 26
- 3-5. Needle bar 28
- 3-6. Motor 29
- 3-7. Timing belt 29
- 3-8. Auxiliary shaft 30
- 3-9. Zigzag 31
- 4. ASSEMBLY 33
- 4-2. Auxiliary shaft 34
- 4-3. Timing belt 34
- 4-4. Motor 35
- 4-5. Needle bar 36
- 4-8. Presser foot mechanism 38
- 4-9. Cover 39
- 5. ADJUSTMENT 41
- X2.4 rotary hook : 2.4 mm 46
- X1.7 rotary hook : 1.8 mm 46
- X2.4 rotary hook : 1.2 mm 46
- 5-4. Tension release 49
- 5-5. Thread tension 49
- <Thread guide, R> 50
- <Fixed knife> 51
- <Needle> 51
- 5-11-1. Folding clamp 56
- 5-11-2. Inner clamp 56
- 5-11-3. Center blade 56
- 5-11-4. Sewing clamp 57
- 5-11-9. Stacker wiper 59
- 5-11-10.Stacker bar inside 59
- 5-11-11. Stacker bar outside 59
- 5-11-12. Stacker roller 60
- 5-30-2. Setting of MODE 73
- <Operation panel> 76
- <Programmer> 76
- 6-3. Power supply 77
- 6-4. PROM 80
- 6-5. Connector 81
- P3 [TRIM] (MOLEX 5273-02A) 82
- P4 [POWER] (MOLEX 5566-10A) 82
- P7 [FDD] (3 M 3431-6002SCFL) 84
- P23 [CLAMP] (MOLEX 5045-03A) 88
- 6-5-2. Power supply PCB 91
- P1 [MAIN] (MOLEX 5277- 04A) 91
- P4 [AC-IN] (MOLEX 5277 - 06A) 91
- 6-5-3. Operation panel PCB 92
- 6-5-4. Programmer PCB 94
- P2 [MAIN] (MOLEX 5268-12A) 94
- 6-5-5. Pattern sensor PCB 95
- 6-6. Sensor 96
- 6-6-2. Function of sensor 97
- < Jig pattern sensor > 99
- < Cylinder sensor > 100
- < Clamp-in sensor > 101
- BAS-7610 102
- 6-7. Harness 103
- 6-8. Servo amplifier 115
- < Servo motor > 116
- 6-9. DIP switches 119
- 6-10. Error code 121
- 6-11. Exchange of PCB 125
- 6.ELECTRIC COMPONENTS 126
- 6. ELECTRIC COMPONENTS 127
- 7. FOLDING MACHINE 131
- 7-2. Valve 133
- 7-4. Adjustment 136
- Tucking blade R-3J 138
- Tucking blade L-3J 138
- Tucking blade LD-3J 138
- Tucking blade RD-3J 138
- D. Program defect 139
- C. Program defect 140
- B. Program defect 142
- E. Program defect 148
- D. Program defect 149
- A. The flap margin is small 153
- A. The flap margin is small 156
- A. The flap margin is large 157
- 21. The pocket top is narrow 162
- 22. The seam margin is large 163
- <Cause> 168
- Tucking blade D 172
- Tucking blade RDD or LDD 172
- 1 - 2 mm 172
- Tucking blade RD 172
- 4. The base is curved 173
- 8. The corners are round 177
Related products and manuals for Sewing machines Brother BAS-761
(91 pages)
(2 pages)
Sewing machines Brother 681B-UG User Manual
(39 pages)
(39 pages)
(68 pages)
Sewing machines Brother LS-2720 User Manual
(15 pages)
(15 pages)
© 2020, manymanuals.com. All rights reserved. | 0.145 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals