Brother Z-8550A Instruction Manual Page 49
- Page / 96
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Z-8550A, 8560A
7. USING THE OPERATION PANEL (ADVANCED OPERATIONS)
40
7. USING THE OPERATION PANEL
(ADVANCED OPERATIONS)
The operations described in this section should only be carried out by a technician.
7-1. Names and functions
(29) Slow start key
• When this key is pressed so that the slow start icon (33) illuminates, the first three
stitches sewn after the thread is trimmed are sewn at slow speed (220 rpm). After this,
the sewing speed corresponds to the treadle depression amount.
• If you press this key again while the icon (33) is illuminated, the icon (33) will turn off.
(30) Correction key
• When this key is pressed so that the correction icon (34) illuminates, correction sewing
can be carried out.
When the treadle is at the neutral position and the actuator is pressed once gently, one
stitch is sewn and then sewing stops; when the actuator is pressed continuously, sewing
is carried out at 220 rpm.
NOTE:
• If you press the actuator while sewing is in progress, backtack stitches will be
sewn.
• If sewing pattern [ 5- *A] or [ 6- *A] is selected, the actuator can be used to
switch to reflection patterns, so that correction sewing cannot be carried out.
(Correction sewing is possible if the setting is [ 5- *_ ] or [ 6- *_ ].)
• If you press this key again while the icon (34) is illuminated, the icon (34) will turn off.
(31) Needle up/down key
Use this key to select whether the needle bar stops in the up position or the down position
when the treadle is returned to the neutral position and sewing stops.
• When the needle up icon
(35) is illuminated, the needle bar stops in the up position.
• When the needle down icon
(36) is illuminated, the needle bar stops in the down
position.
(32) P1key, P2key
This key is used when retrieving user programs.
• This key is disabled if no user programs are available.
3449M
3450M
2207M 2208M 3451M
These are used for making
advanced operating settings.
They should only be used by a
technician.
* The illustration shows the Z-ST (for 8550A-031).
3448M
3452M 3453M
- Z-8550A 1
- Z-8550A, 8560A 2
- SAFETY INSTRUCTIONS 3
- DANGER 3
- CAUTION 3
- Environmental requirements 4
- Installation 4
- Cleaning 5
- Maintenance and inspection 6
- Oil pan 7
- (For Europe) 7
- CONTENTS 8
- 1. NAMES OF MAJOR PARTS 10
- 2. MACHINE SPECIFICATIONS 11
- 3. SEWING PATTERN TABLE 12
- 4. INSTALLATION 13
- <Standard type> 14
- <Wide type> 14
- 4-2. Installation 15
- 6. Knee lifter complying bar 16
- 7. Machine head 16
- 8. Operation panel 16
- 9. Sticker (Remove) 16
- 5. Rubber cushions 16
- 10. Cotton stand 17
- 11. Knee lifter plate 17
- CAUTION 18
- DANGER 19
- 3. Closing the cover 21
- 4. Power cord 21
- 5. Ground wire 21
- 2114M 3374M 22
- 4-5-2. Operating the treadle 23
- 5. PREPARATION BEFORE SEWING 24
- Setting for 1st turn 27
- Setting for 2nd turn 27
- (Zigzag width) 27
- Stitch length 27
- 5-7. Backtacking 28
- 5-8. Using the knee lifter 29
- 6. USING THE OPERATION PANEL 30
- (BASIC OPERATIONS) 30
- 3320M3333M, 3334M3348M 34
- [1] Plain zigzag 35
- [2] 2-step zigzag 35
- [3] 3-step zigzag 35
- [4] Straight stitching 35
- [5] Blind stitching 36
- [6]Scallop patterns 37
- <Reflection patterns> 38
- [7] T stitch 39
- <Setting method> 40
- <Automatic sewing> 45
- Illuminated 47
- 7. USING THE OPERATION PANEL 49
- (ADVANCED OPERATIONS) 49
- 2138M 2139M 50
- 7-3. LOCK key 51
- 7-5. Using user programs 52
- 8. SEWING 55
- 9. THREAD TENSION 56
- Becomes stronger 57
- Becomes weaker 57
- 10. CLEANING 58
- Lubrication 59
- 3. Checking 60
- <Applying grease> 62
- 11. REPLACING PARTS 64
- Example: 65
- 12. STANDARD ADJUSTMENTS 68
- Highest position 71
- Lowest position 71
- Lower the front 72
- Raise the front 72
- Touching 73
- Maximum zigzag width 74
- 12-13. Adjusting the treadle 76
- Nylon thread 78
- Stronger 78
- Seen from direction B 78
- Should not touch 79
- 13. OPTIONAL PARTS 80
- <Installation> 81
- (8560A only) 82
- 15. TROUBLESHOOTING 83
- Voltage rating label 93
- Err 790 94
- Err 791 94
- INSTRUCTION MANUAL 96
Related products and manuals for Sewing machines Brother Z-8550A
Sewing machines Brother QC-1000 User Manual
(162 pages)
(162 pages)
Sewing machines Brother TN-872A User Manual
(152 pages)
(152 pages)
Sewing machines Brother S-7200C Service Manual
(172 pages)
(172 pages)
Sewing machines Brother 882-W04 User Manual
(24 pages)
(24 pages)
Sewing machines Brother BE-438F User Manual
(54 pages)
(54 pages)
Sewing machines Brother PR-620 Specifications
(333 pages)
(333 pages)
© 2020, manymanuals.com. All rights reserved. | 0.241 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals